Suppliers with verified business licenses
TYBT8 is a low power-consuming embedded Bluetooth module developed by Hangzhou Tuya Information Technology Co., Ltd. It consists of a highly integrated Bluetooth chip (TLSR8269) and a small number of peripheral circuits, with a built-in Bluetooth network communication protocol stack and robust library functions. TYBT8 also contains a 32-bit low power-consuming MCU, BLE/2.4G radio, 512 KB flash, 32 KB SRAM, and nine reusable I/O interfaces. Figure 1.1 shows the architecture of TYBT8.
Compatible with BLE 4.2 RF data rate: up to 2 Mbit/s TX power: +7 dBm RX sensitivity: -92 dBm @ BLE 1 Mbit/s Built-in AES encryption for hardware External antenna Working temperature: -40ºC to 105ºC
TYBT8 provides a total of six pins on the front and back sides for plug-in assembly.
TYBT8 size: 8.5 mm (W) x 12.5 mm (L) x 2.4 mm (H)
Figure 2.1 shows the overall pin layout of TYBT8.
Table 2.1 describes the interface pins. Table 2.1 TYBT8 interface pins
No. | Symbol | I/O Type | Functions |
---|---|---|---|
1 | ANT | I/O | RF signal input and output port |
2 | GND | P | Module power supply reference ground pin |
3 | PWM0 | I/O | Common I/O interface, which can be used for PWM output of LED drives |
4 | PWM1 | I/O | Common I/O interface, which can be used for PWM output of LED drives |
5 | PWM4 | I/O | Common I/O interface, which can be used for PWM output of LED drives |
6 | 3.3V | P | Module power supply input pin |
TP1 | SWS | I/O | Test point: Bluetooth chip programming pin |
TP2 | RST | I | Test point: Module reset pin |
TP3 | TX | I/O | Serial port sending pin, which can be used as a common I/O interface |
TP4 | RX | I/O | Serial port receiving pin, which can be used as a common I/O interface |
Note: P indicates power-supply pins, and I/O indicates input/output pins. The SWS pin is used only for programming of module firmware.
Table 3.1 Absolute electrical parameters
Parameter | Description | Minimum Value | Maximum Value | Unit |
---|---|---|---|---|
Ts | Storage temperature | -20 | 125 | ºC |
VCC | Power-supply voltage | -0.3 | 3.9 | V |
Static electricity voltage (human model) | TAMB -25ºC | - | 2 | KV |
Static electricity voltage (machine model) | TAMB -25ºC | - | 0.5 | KV |
Table 3.2 Normal electrical conditions
Parameter | Description | Minimum Value | Typical Value | Maximum Value | Unit |
---|---|---|---|---|---|
Ta | Working temperature | -20 | - | 105 | ºC |
VCC | Working voltage | 1.9 | 3.3 | 3.6 | V |
VIL | I/O low-level input | -0.3 | - | VCC x 0.3 | V |
VIH | I/O high-level input | VCC x 0.7 | - | VCC | V |
VOL | I/O low-level output | VSS | - | 0.3 | V |
VOH | I/O high-level output | VCC - 0.3 | - | VCC | V |
Table 3.3 TX power consumption during constant emission
Symbol | Condition | Typical Value | Unit |
---|---|---|---|
ITX | Constant sending with 0 dBm output power | 15 | mA |
IRX | Constant receiving | 12 | mA |
IDC | Mesh connected | 27 | mA |
Isleep | Sleep mode with I/O waked up | 10 | uA |
Ideepsleep | Deep sleep mode | 1.7 | uA |
Table 4.1 Basic RF features
Parameter | Description |
---|---|
Frequency band | 2.4 GHz ISM band |
Radio standard | BLE 4.2 |
Data transmission rate | 1 Mbit/s and 2 Mbit/s |
Antenna type | External antenna |
Table 4.2 TX power during constant emission
Parameter | Minimum Value | Typical Value | Maximum Value | Unit |
---|---|---|---|---|
RF average output power | 3.8 | 7 | 8 | dBm |
20 dB modulation signal bandwidth (1 M) | - | 1300 | - | KHz |
20 dB modulation signal bandwidth (2 M) | - | 2600 | - | KHz |
Table 4.3 RX sensitivity
Parameter | Minimum Value | Typical Value | Maximum Value | Unit | |
---|---|---|---|---|---|
RX sensitivity | 1Mbit/s | -93 | -92 | -90 | dBm |
RX sensitivity | 2Mbit/s | -90 | -89 | -86 | dBm |
Frequency offset error | 1Mbit/s | -300 | - | +300 | KHz |
Frequency offset error | 2Mbit/s | -200 | - | +200 | KHz |
Co-channel interference suppression | - | - | -7 | - | dB |
TYBT8 uses an external spring antenna, and the specific gain and size can be customized according to customer requirements.
To ensure optimal RF performance, it is recommended that the antenna on the module be at least 15 mm away from other metal parts. If the antenna is wrapped with metal materials, the wireless signal will be significantly attenuated, thereby deteriorating the RF performance. Because the module is installed as a plug-in, reserve enough space for the antenna.
Storage conditions of a delivered module are as follows:
Precautions:
FAQ1.Is it possible order 1pcs? |
Suppliers with verified business licenses