Suppliers with verified business licenses
TYBT2-IPEX is a Bluetooth (BLE) module designed by HangZhou Tuya Technology Corporation. The BLE Module consists of a highly integrated wireless Bluetooth chip TLSR8266 and some extra electric circuits that have been programed with Bluetooth network protocol and plenty of software examples. TYBT2-IPEX include a 32-bit CPU, BLE/2.4G radio, 512K byte flash, 16k SRAM, and 9 multiplex IO pins.
Figure 1 shows the block diagram of the TYBT2-IPEX.
Figure 1. The block diagram of the TYBT2-IPEX
Compatible with BLE 4.0
Transmitting data rate can go up to 2Mbps
TX transmitting power: +7dBm
RX receiving sensitivity: -92dBm
AES hardware encryption
External 2.4G Antenna
Operating temperature range: -20ºC to 105ºC
Intelligent LED
Intelligent household applications
Intelligent low-power consumption sensors
TTYBT2-IPEX have double sides of pins. The distance between each Pin is 1.5mm.
Size of TYBT2-IPEX: 15mm(W)*15.2mm(L).
Figure 2 shows the dimensions of TYBT2-IPEX.
Table 1 shows the general pin attributes of TYBT2-IPEX
Table 1. The typical pin definition of TYBT2-IPEX
PIN NO. | NAME | TYPE | DESCRIPTION |
---|---|---|---|
1 | SDA | I/O | I2C, data interface, internal pull-up 4.7k resistance |
2 | SCL | I/O | I2C, clock interface, internal pull-up 4.7k resistance |
3 | G | I/O | normal IO pin, can be used as PWM output pin, default for Green LED line |
4 | B | I/O | normal IO pin, can be used as PWM output pin, default for Blue LED line |
5 | WW | I/O | normal IO pin, can be used as PWM output pin, default for Warm White LED line |
6 | CW | I/O | normal IO pin, can be used as PWM output pin, default for Cold White LED line |
7 | R | I/O | normal IO pin, can be used as PWM output pin, default for Red LED line |
8 | 3.3V | P | Supply voltage |
9 | TX | I/O | UART TX,can be used as normal IO pin |
10 | RX | I/O | UART RX,can be used as normal IO pin |
11 | GND | P | Ground |
12 | SW | I/O | Bluetooth chipset burning pin |
13 | RST | I | reset pin for the module,internal pull-up 4.7k resistance |
14 | GND | P | Ground |
Note:P: Power supply pins; I/O: Digital input or output pins.
SW pin is ONLY used for burning firmware, Can NOT be used for other functions.
While Pin4 and Pin12 are used for I2C functions, external 4.7k pull-up resistances are necessary.
When WW pin is outputting PWM signal, It has opposite phase comparing the PWM signal from R/G/B/CW pin.
If there's any customization needed for PWM output, please contact our BD manager.
Table 2. Absolute Maximum Ratings
PARAMETERS | DESCRIPTION | MIN | MAX | UNIT |
---|---|---|---|---|
Ts | Storage temperature | -20 | 85 | ºC |
VCC | Supply voltage | -0.3 | 3.9 | V |
Electrostatic release quantity (Human body model) | TAMB-25ºC | - | 2 | KV |
Electrostatic release quantity (Machine model) | TAMB-25ºC | - | 0.5 | KV |
Table 3.2 Electrical Conditions
PARAMETERS | DESCRIPTION | MIN | TYPICAL | MAX | UNIT |
---|---|---|---|---|---|
Ta | Temperature for Commercial grade | -20 | - | 85 | ºC |
VCC | Supply voltage | 2.5 | 3.3 | 3.6 | V |
VIL | IO negative level input | -0.3 | - | VCC*0.25 | V |
VIH | IO positive level input | VCC*0.75 | - | VCC | V |
VOL | IO negative level output | - | - | VCC*0.1 | V |
VoH | IO positive level output | VCC*0.8 | - | VCC | V |
Table 3.3 TX current consumption
PARAMETERS | MODE | TYPICAL | UNIT |
---|---|---|---|
Itx | Continuously transmitting, 0dBm power output | 13 | mA |
Irx | Continuously receiving | 13 | mA |
IDC | Normal working mode | 80 | uA |
Table 4.1 Basic Radio frequency characteristics
PARAMETERS | DESCRIPTION |
---|---|
Working Frequency | 2.4GHz ISM band |
Radio standard | BLE 4.0 |
Data transmitting rate | 1Mbps, 2Mbps |
Type of Antenna | External 2.4G Antenna |
Table 4.2 Transmitting power
PARAMETERS | MIN | TYPICAL | MAX | UNIT |
---|---|---|---|---|
RF Average output power consumption | 3.8 | 7 | - | dBm |
20dB bandwidth | - | 1000 | - | KHz |
Table 4.3 Receiving sensitivity
PARAMETERS | MIN | TYPICAL | MAX | UNIT | |
---|---|---|---|---|---|
RX sensitivity | 1Mbps | -93 | -92 | -90 | dBm |
Frequency bias error | - | -300 | - | 300 | KHz |
Co-channel interference Restrain | - | - | -7 | - | dB |
TYBT2-IPEX requires an external 2.4GHz band antenna with an I-PEX generation terminal on one end.
In order to have the best RF performance, it's recommended to keep a minimum 15mm distance between the antenna part and the other metal pieces. Also,in order to minimize the attenuation of RF performance and to facilitate the free emission of RF signals,the antenna is preferably placed close to the edge,meanwhile, the antenna can not be surrounded by metal objects, can not be blocked by some high devices. To ensure good isolation,when there are two or more antennas of the same frequency band, the distance between the antennas should be widened as much as possible, it is preferably greater than 5 cm.
Figure 4. Dimensions of the module
The storage for the delivered module should meet the following condition:
Cautions:
FAQ1.Is it possible order 1pcs? |
Suppliers with verified business licenses